[Feb-2024] Use Real HPE0-S59 Dumps - 100% Free HPE0-S59 Exam Dumps
HPE0-S59 PDF Dumps Exam Questions – Valid HPE0-S59 Dumps
HPE0-S59 exam is a multiple-choice exam that covers a range of topics related to HPE compute solutions. These include HPE ProLiant servers, HPE SimpliVity hyperconverged solutions, HPE Synergy composable infrastructure, HPE OneView, HPE Integrated Lights Out (iLO), and HPE Smart Array Controllers. HPE0-S59 exam also covers important concepts related to HPE compute solutions, such as virtualization, cloud computing, and software-defined infrastructure.
NEW QUESTION # 16
Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.
What should you do to resolve this issue?
- A. Remove the offline disks using array management tools
- B. Install and configure MPIO on me Windows system
- C. Remove the offline disks using Windows Disk Management
- D. Disable deduplication for this volume at the array level
Answer: B
NEW QUESTION # 17
Your customer reports that they cannot deploy HPE Synergy compute nodes using HPE OneView for VMware vCenter Server (HPE OV4VC).
What should you check during troubleshooting process?
- A. If vCenter Server is licensed in the HPE Oneview interface
- B. If the HPE Oneview instance Is integrated with HPE OV4VC.
- C. If HPE OneView credentials are added in vCenter Server
- D. If an compute nodes are added to the vCenter Server
Answer: D
NEW QUESTION # 18
Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.
Which HPE compute system meets this customer's requirements?
- A. HPE Synergy 480 Gen10 Plus
- B. HPE ProLiant DL380 Gen 10 Plus
- C. HPE Superdome Flex 280
- D. HPE ProLiant DL560 Gen10
Answer: B
NEW QUESTION # 19
Which statement about a new HPE SimpliVity deployment is true?
- A. All new HPE SimpliVity models are based on AMD CPUs
- B. New HPE SimpliVity deployments are licensed per node not per physical socket
- C. New HPE SimpliVity deployments give customer flexible choice of hypervisor
- D. All new HPE SimpliVity models support deduplication and compression
Answer: D
NEW QUESTION # 20
Which statement about HPE OneView milestone releases is true?
- A. A milestone release is a release which must be installed on HPE Composer to support current version of the Service Pack for Synergy
- B. A milestone release is a release with an enhanced update architecture mat is a prerequisite prior to updating to a subsequent release.
- C. A milestone release is a release that is published when HPE releases new hardware components to immediately support new systems
- D. A milestone release is available for selected partners that give access to HPE OneView features which are not officially announced.
Answer: A
NEW QUESTION # 21
Refer to the exhibit.
Which statement about this logical JBOD is true?
- A. After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done
- B. This logical JBOD can be presented to the compute nodes in a different frame.
- C. After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created
- D. This logical JBOD can be connected to multiple systems to formulate a snared datastore.
Answer: A
NEW QUESTION # 22
You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?
- A. App Volume Set
- B. Virtual Volume Set
- C. virtual Volume
- D. Storage Container
Answer: B
NEW QUESTION # 23
Which statement about an HPE Oneview support dump is true?
- A. Support dump can be created if HPE Virtual Connect modules are installed in the frame
- B. Preview support dump is available only when creating an appliance support dump
- C. Appliance support dump by default contains a logical enclosure support dump
- D. Support dump is a binary file that can be opened only in a dedicated application
Answer: D
NEW QUESTION # 24
Which compute node parameters are captured within server hardware type?
- A. Number of the CPUs
- B. Size of the memory Installed
- C. installed operating system
- D. Mezzanine card configuration
Answer: C
NEW QUESTION # 25
Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?
- A. HPE SUM if HPE Persistent Memory firmware must be updated
- B. HPE OneView method for I/O firmware update procedure
- C. HPE OneView IT HPE Persistent Memory firmware must be updated.
- D. RMC CLI to update I/O and HPE Persistent Memory firmware
Answer: D
NEW QUESTION # 26
Click the area within the iLO management interface that will allow you to access workload Advisor.
Answer:
Explanation:
NEW QUESTION # 27
Your customer is implementing an HPE Synergy solution based on three frames.
Click each of the ports that can be used to connect satellite modules.
Answer:
Explanation:
NEW QUESTION # 28
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard licenses for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options Which statement about this proposal is true?
- A. vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
- B. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
- C. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
- D. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.
Answer: A
NEW QUESTION # 29
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A. interconnect modules are installed in interconnect bays 1 and 4
- B. Both modules are located in different frames for redundancy
- C. An additional license is required to change the enclosure count
- D. For an uplink set, ports from different modules can be selected
Answer: C
NEW QUESTION # 30
You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.
Put the steps to achieve this goal into the coned order in the answer area on the right.
Answer:
Explanation:
NEW QUESTION # 31
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex
280 They plan to manage new components using HPE OneView
What must be done to achieve this goal?
- A. The customer should deploy an HPE OneView appliance for HPE Superdome Flex management
- B. The customer must add a second Rack Management Controller for HPE Superdome Flex 280
- C. The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView
- D. The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy
Answer: B
NEW QUESTION # 32
Which statement about HPE Apollo 2000 Gen10 Plus platform is true?
- A. It can support a single processor only and up to 4 per chassis
- B. It is fully managed using HPE OneView including all connections
- C. It offers servers with AMD EPYC and Intel Xeon Scalable CPUs
- D. It is equipped with HPE Persistent memory by default
Answer: A
NEW QUESTION # 33
Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?
- A. Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules
- B. FC connectivity on the modules should be enabled through the service console by disabling FCoE.
- C. Enter both modules into a maintenance mode, then enable FC connectivity through CLI
- D. Enable FC primary and secondary boot on the modules through the HPE OneView interface
Answer: B
NEW QUESTION # 34
Your customer has me following HPE Synergy setup
- Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
- Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
- Four HPE Synergy 50Gb interconnect Link Module
- Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?
- A. The additional frame cannot have 12Gb SAS connection modules installed
- B. The customer has to create a new logical enclosure for the additional frame
- C. The additional frame must have HPE Virtual Connect FC modules installed
- D. The customer can grow the existing logical enclosure up to 5 frames
Answer: B
NEW QUESTION # 35
......
Ultimate HPE0-S59 Guide to Prepare Free Latest HP Practice Tests Dumps: https://passleader.examtorrent.com/HPE0-S59-prep4sure-dumps.html
