Free Senior-Internal-Corrosion-Technologist Exam Study Guide for the NEW [Mar-2025] Dumps Test Engine
Senior-Internal-Corrosion-Technologist PDF Dumps Extremely Quick Way Of Preparation
NEW QUESTION # 37
The primary purpose of Fireproofing coatings are to provide:
- A. Fire extinguishing characteristics
- B. Preferential fuel for the file
- C. Explosion resistance
- D. Temporary protection for the structure
Answer: D
NEW QUESTION # 38
When working with someone who Is very concerned about stability and maintaining adherence to the status- quo, the Inspector should try to:
- A. Give them as much advance notice as possible about upcoming changes
- B. Make sure they are the center of attention in all site meetings
- C. Challenge their value to the team and try to get them out of their comfort zone
- D. Implement Immediate changes to get them motivated
Answer: A
NEW QUESTION # 39
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Flow stage
- B. Cure stage
- C. Getstage
- D. Wetting stage
Answer: A
NEW QUESTION # 40
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Move the nozzle quicker
- C. Lower the blast pressure
- D. Increase the standoff distance
Answer: A
NEW QUESTION # 41
An Inspection and Test Plan is required when:
- A. When the Coating Applicator requests one
- B. When the Owner specifies one
- C. When the Inspector requests one
- D. It is always required
Answer: D
NEW QUESTION # 42
Coating application to concrete substrates is:
- A. The same as coating steel
- B. Less challenging than coating steel
- C. Not required as concrete is Inorganic
- D. More challenging than coating steel
Answer: D
NEW QUESTION # 43
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed.
The specification references SSPC SP 16 as the surface preparation method. At the pre-Job meeting operations personnel make it dear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used. Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by acid etching
- C. SP 1 followed by SP 3
- D. SP 1 followed by SP 2
Answer: B
NEW QUESTION # 44
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Latex
- B. Inorganic Coatings
- C. Organic coatings
- D. Polyurea
Answer: D
NEW QUESTION # 45
Thermal Spray coatings provide:
- A. inhibitiveprotection
- B. Thermal protection
- C. Barrier protection
- D. Sacrificial protection
Answer: C
NEW QUESTION # 46
When performing testing in accordance with ASTM D 2583 the Inspector may observe:
- A. Glue failure
- B. Cohesion failure
- C. Cold flow or creep
- D. Adhesion failure
Answer: C
NEW QUESTION # 47
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection only
- C. All types of inspection without supervision
- D. Visual inspection and Non-destructive testing
Answer: A
NEW QUESTION # 48
You are theNACE Coating Inspector on a tank lining project and are asked to perform ahigh voltage holiday test after thecoating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course or action should be to:
- A. Don your air supplied respirator and continue the testing
- B. Exit the tank and document the incident in your dally report
- C. Exit the tank and Immediately and report the problem to the nearest safety supervisor
- D. Investigate to find the source of the odor
Answer: C
NEW QUESTION # 49
NACE No. 13/ SSPC 6 Identifies the use of:
- A. Various methods of cleaning
- B. Abrasive blasting only
- C. Watterjetting only
- D. Steam cleaning only
Answer: A
NEW QUESTION # 50
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the contractor has a single document to reference
- C. Outline the Inspection steps, sequencing and pass/fail criteria
- D. So the Inspector doesn't have to read the entire specification
Answer: C
NEW QUESTION # 51
Centrifugal blast cleaning requires:
- A. A large volume of alt to propel the abrasive
- B. The use of single use abrasives
- C. Very large nozzles
- D. Well maintained blast wheels
Answer: D
NEW QUESTION # 52
II Is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION # 53
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: B
NEW QUESTION # 54
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Distilled water
- C. standard buffer solution
- D. Standard solvent solution
Answer: C
NEW QUESTION # 55
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Different than air blast cleaning
- C. The same as air blast cleaning
- D. Comparable to air blast cleaning
Answer: C
NEW QUESTION # 56
Generally,for safety considerations, waterjetting hose connections use
- A. a whip-lock device.
- B. an oil/water separator.
- C. filters.
- D. a long wand.
Answer: A
NEW QUESTION # 57
When environmental enclosures ate being used an inspector needs to be concerned about:
- A. a), b), and c)
- B. Air changes
- C. Structural integrity
- D. Lighting
Answer: A
NEW QUESTION # 58
The HATE adhesion tester uses
- A. mechanical means only to apply pressure to the test dolly.
- B. compressed air to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. a hydraulic piston to apply pressure to the test dolly.
Answer: D
NEW QUESTION # 59
When measuring the Dry Film Thickness of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument Is the:
- A. Magnetic Gauge
- B. Ultra Sonic DFT Gauge
- C. Tooke Gauge
- D. Eddy Current Gauge
Answer: B
NEW QUESTION # 60
You are a NACE Level 2 in-house inspector working in a shop. Your In-house UP requires you to perform a sleeve test to test for soluble sails; however the 3rd party NACE Level 3 inspector, representing the owner, has used a salt smart meter and has achieved a very different result and has rejected the pre cleaning.
Your FIRST preferred course of action is to:
- A. Advise your QC Manager to change the UP to the use of the salt smart meter
- B. Advise the other Inspector he is using an Incorrect method
- C. Review the specification with the other inspector to see what method was specified
- D. Redo the pre-cleaning based on the other Inspectors results
Answer: C
NEW QUESTION # 61
......
Enhance your career with Senior-Internal-Corrosion-Technologist PDF Dumps - True AMPP Exam Questions: https://passleader.examtorrent.com/Senior-Internal-Corrosion-Technologist-prep4sure-dumps.html
